Legendary recording engineer Stan Ricker uses E-SST Super Silver Treatment and the Velocitor Power Line Enhancer and in his mastering system.  See what he says about them:  E-SST    Velocitor   

Discover New 

Uses For E-SST 

EXTREME SST

Super Silver Treatment

Reveals sonic details and

harmonics you’ve been missing.

Click to view larger photo.

As one reviewer wrote:

"leave it to Lloyd (Walker Audio) to improve something you are happy with already"  and we did.

Extreme SST is easily 20 to 30% better than the original.

and original

SST 

 Super Silver Treatment

for all electrical contacts

Click to view larger photo.

Comes with enough product to treat your system many times over and to share with your friends. Twelve applicators included.

While developing SST – Super Silver Treatment, we tested many types of conducting substances and carrier fluids. We chose an ultra-pure, thin, long micron-sized silver flake suspended in an organic fluid for its dielectric characteristics and excellent sound. We believe E-SST/SST are vastly superior compared to any contact treatment on the market today.

Most contact treatments on the market are either cleaners or lubricants. They are not conductive. E-SST/SST is highly conductive and must be applied with care according to directions. 

E-SST/SST will dramatically improve the sound and/or video of any system.  The highs will be more extended, cleaner, clearer and better focused. The mid-range will be more transparent with more articulation and detail, yet without harshness or glare. The bass will be stronger, tighter, and quicker. The soundstage will take on a more natural presence. With video systems, the sound improvement will be matched by the improvements to the video. Look for a cleaner, more three-dimensional picture. 

CAUTION!!! Use at your own risk. Please read the instructions fully before proceeding. E-SST/SST is highly conductive. If you bridge the gap between hot and ground with E-SST/SST, you run the risk of damaging your system. Used as directed. E-SST/SST can be removed by using a clean cotton swab or one of the unused applicators dipped in alcohol, fingernail polish remover, or contact cleaner.

Treating Interconnects

Use one of the supplied applicators to apply a very small amount of E-SST/SST to the male end of the interconnect. Spread it thinly on about ½ or ¾ of the length of the center pin. Apply E-SST/SST to the outside only of the female end in a thin even coat. Now, plug in your interconnect and listen. On XLR interconnects, apply to male pins only.   DO NOT put the applicator into the RCA or you will short it out. 

Treating Power Cords

Apply a thin even coat of E-SST/SST to the male ends only. Cover both sides of the pins about half the length of the pins. On the I.E.C. male end at the component, do the same. Use only a very small amount. Do not over apply.

Treating Speaker Cables

Apply a thin even coat of E-SST/SST to the contact area of the spades or bananas.

Treating Tubes

We experienced a big improvement when we applied E-SST/SST to the pins of the tubes in our amplifiers. We suggest cleaning the pins with fine sandpaper in the direction on the pins. Clean with a contact cleaner, then apply a thin, even coat of E-SST/SST to about 2/3 the length of the male pin.

Video/Other Uses

E-SST/SST works great on video connectors. Apply to the male pins and the outside of female connectors.  E-SST/SST also works on fuses and any contact device. 

Guarantee Of Satisfaction

We think you will be amazed. If not, you may return the unused portion within 30 days for a full refund, less shipping.

HOW TO APPLY E-SST/SST

Whether you are putting it on audio and video equipment or something else, the same rules apply.  It is best to clean the connections with a contact cleaner that leaves no residue. If the contact is corroded, you can lightly sand or scrape it. Then clean it. 

Apply a very thin (almost transparent) coat of E-SST or SST to the male end of the connector. I’ve been asked which is the male end. For the uninitiated, the male end of a connector is the part that sticks out....think anatomy! Apply to the male end or to the ring connector or to the end of the spark plug that the plug wire goes to. Remember, very thin. More is not better. 

REMOVE EXCESS

If you get too much, use alcohol or contact cleaner to remove it. Take your time and pay close attention. Use E-SST and SST at their own risk.  E-SST and SST are very conductive. If you get it across a connection, you can short out your equipment.  When applied properly, you will have no problems. In fact, we guarantee you’ll be satisfied with the results or we will refund the purchase price.  

IF PASTE GETS TOO THICK

Over time, E-SST and SST will dry to a thick paste. This is by design so that it does not migrate. Use two or three drops of the supplied fluid. Add one drop at a time and stir with a wooden toothpick to achieve a consistency that is easy to work with. You can also use Canola oil available at most grocery stores. 

BREAK-IN PERIOD

E-SST/SST will immediately make a significant improvement. It will be even better after eight to ten hours of break-in time for the treated connectors.

RECONNECTING/REAPPLYING

Before reconnecting, it is beneficial to take a used applicator with the SST wiped off (some will still be embedded in the applicator) and spread over the connector. This will help to distribute the SST that remains on the connector. If you reapply it, make sure there is not excessive SST on the connector. If there is, clean it as directed above before applying more. If you have any questions about how to use this product, call us.

NEW USES FOR E-SST/SST

Customers are applying E-SST to every electrical connection you could image. We thought putting it on a hair dryer was bit unusual, but my favorite is the customer who put it on his weed whacker. Lawnmowers and other outdoor equipment with engines can benefit from it.  See link at top of this page for our motorcycle experience.

Advanced Uses

We've heard from our more adventurous customers, reviewers and manufacturers who have applied E-SST to the inside connections of projectors, computers, and DVD players and we've done this ourselves as well. The results are astounding.

This is not recommended for most people, only for qualified electronic technicians. The inside connections are very small and close together and can be fragile. Use a bright light and magnifying glasses to see the connections and a sharp toothpick to apply E-SST. Use only a tiny amount on ¼ to ½ of the pin. And use extreme care to avoid damaging the connectors and/or shorting out your equipment.   

If you have any questions about E-SST or SST,